Builders Hardware

The Outdoor Accents structural screw reduces installation time by driving easily without predrilling. When combined with the patent-pending load rated Outdoor Accents structural washer the solution...

The Outdoor Accents structural screw reduces installation time by driving easily without predrilling. When combined with the patent-pending load rated Outdoor Accents structural washer the solution delivers the decorative appearance of a bolt connection but with a much easier installation than through-bolting. The structural screw and washer are sold separately from each other and the Outdoor Accents connectors. Its bold thread design enables superior holding to attach ledgers and other...

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation...

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation with 16d commons. A 2" minimum side cover is required to obtain the full load. Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or carports). 12-gauge galvanized steel....

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation...

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation with 16d commons. A 2" minimum side cover is required to obtain the full load. Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or carports). 12-gauge galvanized steel....

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation...

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation with 16d commons. A 2" minimum side cover is required to obtain the full load. Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or carports). 12-gauge galvanized steel....

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation...

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation with 16d commons. A 2" minimum side cover is required to obtain the full load. Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or carports). 12-gauge galvanized steel....

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation...

The PB base embeds in wet concrete after pour and is made to install flush with the concrete surface. This connector was designed to help resist upload forces. Holes are provided for installation with 16d commons. A 2" minimum side cover is required to obtain the full load. Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or carports). 12-gauge galvanized steel....

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps panels even for a level plain on the structure. Quick installation no nails needed. Provides a 1/8" gap between plywood panels as recommended by the American Plywood Association. 20-gauge galvanized steel. No. PSCL 1/2: Size: 1/2 In. Material: Galvanized Steel Gauge: 20 ga Pkg Qty: 1 No. PSCL 15/32:...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps panels even for a level plain on the structure. Quick installation no nails needed. Provides a 1/8" gap between plywood panels as recommended by the American Plywood Association. 20-gauge galvanized steel. No. PSCL 1/2: Size: 1/2 In. Material: Galvanized Steel Gauge: 20 ga Pkg Qty: 1 No. PSCL 15/32:...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps panels even for a level plain on the structure. Quick installation no nails needed. Provides a 1/8" gap between plywood panels as recommended by the American Plywood Association. 20-gauge galvanized steel. No. PSCL 1/2: Size: 1/2 In. Material: Galvanized Steel Gauge: 20 ga Pkg Qty: 1 No. PSCL 15/32:...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps panels even for a level plain on the structure. Quick installation no nails needed. Provides a 1/8" gap between plywood panels as recommended by the American Plywood Association. 20-gauge galvanized steel. No. PSCL 1/2: Size: 1/2 In. Material: Galvanized Steel Gauge: 20 ga Pkg Qty: 1 No. PSCL 15/32:...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps panels even for a level plain on the structure. Quick installation no nails needed. Provides a 1/8" gap between plywood panels as recommended by the American Plywood Association. 20-gauge galvanized steel. No. PSCL 1/2: Size: 1/2 In. Material: Galvanized Steel Gauge: 20 ga Pkg Qty: 1 No. PSCL 15/32:...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps...

Panel Sheathing Clips are used to brace unsupported panel edges when sheathing meets edge-to-edge without a rafter for support. Select the same size sheathing clip as the panel thickness. Keeps panels even for a level plain on the structure. Quick installation no nails needed. Provides a 1/8" gap between plywood panels as recommended by the American Plywood Association. 20-gauge galvanized steel. No. PSCL 1/2: Size: 1/2 In. Material: Galvanized Steel Gauge: 20 ga Pkg Qty: 1 No. PSCL 15/32:...