Cancel
Account
My Items
My Cart
OR
Filter
Sort By
At-hand regulator allows custom pressure settings for various tools or applications. To set required pressure turn the regulator up to the max 140 psi and adjust downward to required pressure each...
At-hand regulator allows custom pressure settings for various tools or applications. To set required pressure turn the regulator up to the max 140 psi and adjust downward to required pressure each time the pressure setting is changed. Adjusts while in use. 175 Deg maximum operating temperature. No. 41-145: Connection Type: 1/4 In. FNPT Pressure Rating: 140 psi Air Rating: 25 CFM Pkg Qty: 1 Package Type: Clamshell
Thread size: 1/4" Male NPT x 1/4" Male NPT. Brass. 1 per card. No. 21-505: Design: Male Thread Size: 1/4 In. MNPT Material: Brass Pressure Rating: 300 psi Pkg Qty: 1
Gives accurate pressure regulation with maximum water and dirt separation. Increases life of expensive air-powered tools. Solid piston resists rupture cracking or tearing under pressure or high...
Gives accurate pressure regulation with maximum water and dirt separation. Increases life of expensive air-powered tools. Solid piston resists rupture cracking or tearing under pressure or high cycle rates. Maximum operating pressures: 150 psi at 125 Deg. F. primary 2 to 125 psi secondary. Operating temperature range: -10 Deg. F. to +175 Deg. F. Includes filter element and a pressure gauge. Port size: 1/4 In. NPTF. Manual drain. 5 micron element. Bowl capacity - 1 Oz. Overall height: 8-1/2 In....
Non-rising locking knob adjustment. Gauge included two gauge ports. No. 27-444: Connection Type: 1/4 In. NPT Pressure Rating: 250 psi Pkg Qty: 1 Package Type: Box
Lever-type. Conforms to all OSHA (Occupational Safety and Health Organization) requirements including noise level regulations. Features a vented nozzle to relieve the compressed air should the...
Lever-type. Conforms to all OSHA (Occupational Safety and Health Organization) requirements including noise level regulations. Features a vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Tamper proof pressure reducer limits nozzle pressure to 30 psi (pounds per square inch) or less with a maximum inlet pressure of 150 psi. Heavy-duty die-cast body with hang-up hook. 1/4" Female NPT (National Pipe Thread) . 1 per card. No. 18-233: Pressure...
Snap-on chuck clip converts any single foot chuck to a clip-on chuck. Holds chuck to tire valve while inflating. Fits all standard ball foot chucks with .672-32 thread. No. 17-355: Thread Size:...
Snap-on chuck clip converts any single foot chuck to a clip-on chuck. Holds chuck to tire valve while inflating. Fits all standard ball foot chucks with .672-32 thread. No. 17-355: Thread Size: 0.672 In. Threads Per Inch: 32 tpi Pkg Qty: 1 Package Type: Card
Lever-type with hanger hook. Epoxy finish. 1/4" Female NPT inlet. To comply with OSHA standards it must be used on a regulated air line with maximum pressure of 30 P.S.I. 1 per card. No. 18-203:...
Lever-type with hanger hook. Epoxy finish. 1/4" Female NPT inlet. To comply with OSHA standards it must be used on a regulated air line with maximum pressure of 30 P.S.I. 1 per card. No. 18-203: Pressure Rating: 30 psi Inlet Size: 1/4 In. Pkg Qty: 1
Oil-resistant soft replaceable rubber tip. Will not mar delicate surfaces. Gives a leakproof seal against oil passages fuel lines etc. when air pressure is needed for cleaning. 1/4" Female NPT...
Oil-resistant soft replaceable rubber tip. Will not mar delicate surfaces. Gives a leakproof seal against oil passages fuel lines etc. when air pressure is needed for cleaning. 1/4" Female NPT inlet. Allows full line pressure to be used. To comply with OSHA regulations this blowgun must be used on a regulated air line with a pressure setting not to exceed 30 P.S.I. No. 18-207: Pressure Rating: 30 psi Inlet Size: 1/4 In. Pkg Qty: 1
Heavy-duty Turbo Shear shear attachment. Heavy-duty attachment inserts into chuck of 3/8 In. or 1/2 In. drills. Cuts straight and to the left up to 20-gauge galvanized steel also cuts 18-gauge...
Heavy-duty Turbo Shear shear attachment. Heavy-duty attachment inserts into chuck of 3/8 In. or 1/2 In. drills. Cuts straight and to the left up to 20-gauge galvanized steel also cuts 18-gauge steel. Ideal for cutting in ferrous and nonferrous sheet metals metal roofing/building panels vinyl steel mesh and ductwork. Offset design keeps both hands away from work surface. Also makes angled crosscuts through profiles of metal building panels and stone-coated metal shingles. No. TSHD: Chuck Size:...
Turbo Shear. Heavy-duty attachment inserts into chuck of 3/8 In. or 1/2 In. drills. Cuts straight and to the left up to 20-gauge galvanized steel. Ideal for cutting in ferrous and nonferrous sheet...
Turbo Shear. Heavy-duty attachment inserts into chuck of 3/8 In. or 1/2 In. drills. Cuts straight and to the left up to 20-gauge galvanized steel. Ideal for cutting in ferrous and nonferrous sheet metals metal roofing/building panels vinyl steel mesh and ductwork. Offset design keeps both hands away from work surface. No. TS1: Chuck Size: 3/8 In. 1/2 In. Cutting Capacity: Up to 20 Ga. Pkg Qty: 1 Package Type: Clamshell
Precut screens for use with floor sanders including Essex Clarke and American. Resin over resin bonded silicon carbide. 12" x 18". No. 414-824498: Dimensions: 12 In. x 18 In. Grit: 150 Grit Pkg Qty:...
Precut screens for use with floor sanders including Essex Clarke and American. Resin over resin bonded silicon carbide. 12" x 18". No. 414-824498: Dimensions: 12 In. x 18 In. Grit: 150 Grit Pkg Qty: 1 Package Type: Card No. 414-824496: Dimensions: 12 In. x 18 In. Grit: 120 Grit Pkg Qty: 1 Package Type: Card
Virginia Abrasives Grit Floor Sanding Disc